ALLIS CHALMERS - Gyratory Crusher

1 - ALLIS CHALMERS 60in x 89in Gyratory Crusher, S/N 2-1724-97452. No motor. Maximum feed size is 48in. Specs off some of the key components below.

BOTTOM SHELL (BASE) Serial # 2-1724-97452
-This is the straight bottom shell design.
-Lower arm wear minimal.
-Generally good condition
-No Bushings
-Liners worn out
-Mounting holes in good condition.
-Appears in serviceable condition.
-No dust collar found.

LOWER TOP SHELL
-Good condition
-Bolt holes and flanges in good condition

TOP SHELL SECTION
-Good usable condition
-Flange holes in good condition
-Tapers appear good

SPIDER
-Wear on the spider arms
-Serviceable, care should be taken to protect these surfaces when in future use.
-Some wear on the spider arms and the housing.
-Spider to top shell taper appears to be good.
-Spider rim has minimal wear.
-Spider and rim liners available.
-Spider bushing should be measured to insure it conforms to spec.
-Wear on the spider arm and spider bushing outer housing.
-Spider is suitable for further use.

SPIDER ARM LINERS- ARM GUARDS - CONCAVES
-These are used but still have plenty of service life especially if wear bars are welded on for further protection.
-Good condition

MAINSHAFT
-Appears to be in generally good condition.
-Inner head nut usable but should be replaced.
-Main shaft Sleeve is usable but should be replaced.
-Lower journal in good condition.
-Main shaft Step (Bronze) is approximately 70% worn. It is usable as is and could be re-grooved to extend the life.
-Dust Seal retainer has normal wear. It is usable, the attachment bolts will require work to remove.
-The Dust seal should also be replaced due primarily to age.
-The splash curtain is missing.

MAINSHAFT LOWER JOURNAL
-Good condition.

HYDROSET
-Eccentric support plate is in place with eccentric wear plate (bronze)
-Appears to be in usable condition
-Some wear on flanges but usable
-The piston has been removed.
-The upper and lower Hydroset bushings are in place
-Unit has been cleaned and painted.

ECCENTRIC
-60 X 89 Eccentric
-Appears to be in good condition
-Eccentric has been cleaned and painted

BOTTOM SHELL BUSHING
-Bottom shell bushing is used
-Cleaned and useable

ECCENTRIC SUPPORT PLATES
-There are 2
-Both appear to have had little use.
-Unit has been cleaned

PINION SHAFT-COUNTERSHAFT ASSEMBLY
-Pinion serviceable
-Housing in good condition.
-Should be disassembled and evaluated to determine condition of internals for future use.
-Cleaned and painted


SPARES AVAILABLE (Additional Cost)
1 - ea Used Spare Pinion and Countershaft - information on unit as follows:
E61 A.C.CC-35110-C, Shaft-P-61, 10/10/94
8606 Pinion, F.M.D. IL.075 1.G.8496
07-451-501-09-003, 16-Tooth; good condition
Spare Pinion & Countershaft Price $400,000 USD
1 - ea Used Spare Mainshaft
Suitable for use after some clean-up
APPROXIMATE WEIGHTS:
Spider Assembly 17' 11in Wide X 17' 11in Long X 6' high Est. Weight 92,000 Lbs.
Top Shell Assy. 17' 4in Wide X 17' 4in Long X X 8'6in High Est. Wt. 124,000 lbs.
Middle Shell Assy 14'10in Wide X 14' 10in Long x 8' High Est. Wt. 124,000 lbs.
Base Assy. 14' Wide X 14' Long X 6' High Est. Wt. 151,000 Lbs.
Eccentric Assy. 6' Wide X 6' Long X 6' High Est. Wt. 12,000 Lbs.
Mainshaft Assemblies for 60 x 89 22' 2in Long X 6' Diam. 144,700 lbs.

Repairs will be made by reputable machine shop in Arizona.